Literature by the same author
plus at Google Scholar

Bibliografische Daten exportieren

Explanation of the Non-Linear Electrical Behavior of a Resistive NOₓ Dosimeter By Operando DRIFT Spectroscopy

Title data

Moos, Ralf ; Schönauer-Kamin, Daniela:
Explanation of the Non-Linear Electrical Behavior of a Resistive NOₓ Dosimeter By Operando DRIFT Spectroscopy.
Event: The 18th International Meeting on Chemical Sensors, IMCS2021 , May 30 - June 6, 2021 , online conference.
(Conference item: Conference , Speech )

Official URL: Volltext

Abstract in another language

To detect low NOx concentrations is still a focus for air-quality monitoring. The direct detection of the total dose of NOx is beneficial since the air pollution limits are given as hourly and annual mean values. A gas dosimeter for direct detection of the dose of NOx was presented. In the sorption phase, NOx molecules are adsorbed on the functional film and the electrical resistance changes. During this phase, the correlation between NOx dose and resistance change is linear until a certain loading state is reached. As soon as the characteristic curve gets non-linear, described often as saturation of the NOx adsorption, sensor regeneration is necessary. During thermal regeneration, the sorbed NOx species is desorbed from the surface, and a new sorption cycle can begin.

To further understand the sensing mechanism and the effects of non-linearity, NOx dosimeters are investigated by operando DRIFT spectroscopy. The electrical sensor signal and the formation of adsorbed species are investigated operando on the dosimeter. The non-linear behavior of the electrical properties occurring at a certain sensor signal are investigated at various film thicknesses and are combined with the sorption properties.

Potassium-permanganate impregnated on lanthanum-stabilized alumina powder (K/Mn-La-Al2O3) serves as the functional material. It is applied by screen-printing on an alumina substrate equipped with interdigitated Au electrodes and fired at 650 °C. Different layer thicknesses of the functional films are achieved by several screen-printing steps. The sensors are mounted in a gas purgeable operando DRIFTS cell (Fig. 1) and heated by an integrated platinum heating structure to 350 °C. They are exposed to synthetic air (20 % O2 and 2 % humidity in N2 balance). NOx concentrations (ppb-range) are added and validated by a chemiluminescence detector (CLD). The sensor resistance is derived by impedance spectroscopy (f = 200 Hz, Ueff = 200 mV) from an R||C equivalent circuit. The sensor signal is defined as the relative resistance change (R-R0/R0), with R0 being the resistance in base gas and R the resistance during NOx exposure. Simultaneous DRIFT spectra are obtained and the absorbance -log(I/I0), with the intensity I0 in base gas and the intensity I during NOx adsorption, is calculated. The sensors are regenerated by heating up to 650 °C.

An operando DRIFTS result during exposure to three peaks of 50 ppb NOx with NOx pauses in-between is shown in Fig. 2. The NOx dose in ppm∙s is derived from the integration of the CLD NOx signal. The dose increases linearly during NOx exposure and remains constant during dosing pauses. The sensor signal shows the same behavior: ΔR/R0 increases linearly when 50 ppb NOx are present and stays constant during NOx absence. The calculated absorbance shows a clear peak at a wave number of 1370 cm-1 occurring during NOx exposure. It can be attributed to the nitrate formation on potassium sites of K/Mn-La-Al2O3 and is characteristic for the sorption phase. The calculated peak area AE of this nitrate peak is shown in Fig. 2, too. AE and therefore the amount of formed nitrates increases linearly during NOx addition and remains constant during NOx pauses. The electrical properties of the dosimeter can be related directly to the NOx dose and to the formed nitrates. One important point is that all curves increase linearly during NOx exposure and no saturation effects can be observed for the sensor signal and the nitrate formation. In Fig. 3, the sensor is exposed to three peaks of 390 ppb NOx. ΔR/R0 gets non-linear after reaching 40 %. The sensor seems to saturate. The slope during NOx exposure is non-linear and the signal in NOx pauses decreases. In contrast, AE behaves almost linear. It is assumed that the electrically observed non-linearity cannot be explained by a saturation of the adsorption capability of K/Mn-La-Al2O3. It seems that the NOx adsorption capability is not exhausted, but the resistance shows a saturation effect.

The results show that the sensor behaves like a dosimeter with linear characteristics between NOx dose, sensor signal and formed nitrate species until a certain sensor signal of around 40 % is reached. At higher relative resistance changes, the electrical signal becomes non-linear, whereas the adsorption capability itself, i.e. the nitrate formation, remains linear and the NOx adsorption on K/Mn-La-Al2O3 is not saturated. This behavior will be investigated by operando DRIFTS in dependence on the film thickness.

Further data

Item Type: Conference item (Speech)
Refereed: Yes
Institutions of the University: Faculties > Faculty of Engineering Science
Faculties > Faculty of Engineering Science > Chair Functional Materials > Chair Functional Materials - Univ.-Prof. Dr.-Ing. Ralf Moos
Profile Fields > Advanced Fields > Advanced Materials
Research Institutions > Research Centres > Bayreuth Center for Material Science and Engineering - BayMAT
Faculties > Faculty of Engineering Science > Chair Functional Materials
Profile Fields
Profile Fields > Advanced Fields
Research Institutions
Research Institutions > Research Centres
Result of work at the UBT: Yes
DDC Subjects: 600 Technology, medicine, applied sciences > 620 Engineering
Date Deposited: 30 Jun 2021 13:15
Last Modified: 29 Sep 2021 06:57